Extending downspout drainage away from a building

Get roof water away from the foundation with a buried line that has somewhere to go.

A buried downspout line in five stages

A short trench along a house. The planning is about the outlet and the fall; the digging is a few hours with the right machine.

Two or three downspouts on the same side of the house can often share one trunk line to one outlet. Plan that before you dig so you trench once.

Watch the downspouts in a rain

Go outside during a storm. Note which downspouts put water where it pools, which splash blocks are missing or pointed the wrong way, and whether the ground along the wall slopes toward the house. While you are there, look up: a gutter that overflows at the corner is a clog or a sag, and no amount of underground pipe fixes that. Clean the gutter first. One or two downspouts usually cause most of the problem, and those are the ones to extend.

No machine. A camera and a notebook. An extension ladder if the gutters need a look.

Pick where the water comes out

Roof water has to end up somewhere lower than the downspout base. Common outlets: a pop-up emitter in a part of the lawn that already drains, daylight on a slope, a swale or ditch, or a dry well in soil that perks. Measure the drop from the downspout base to the outlet. The pipe has to fall the whole way, and the outlet has to stay open and not freeze shut in the first winter. Confirm the outlet is one you are allowed to use; sending roof water into the street, a storm drain or a neighbor's yard may be restricted in your township.

Line level, stakes, string and a tape.

Mark the line and call MISS DIG

Paint the route from the downspout to the outlet. Utilities are dense along a house: gas service, electric, cable, the water line, and the sewer lateral all come in somewhere along the wall, and irrigation and landscape lighting run everywhere. Contact MISS DIG 811 at least three business days before digging; it is free and required by Michigan law. MISS DIG does not mark private lines. Walk the route with a rental metal detector to look for irrigation valve boxes and old pins, knowing it does not replace the locate. Keep the trench far enough from the foundation that you are not undermining the footing or cutting a footing drain.

Metal detector.

Trench with the right machine

For a straight run from the house out into open lawn, the Ditch Witch C24X trencher cuts a 6 in slot up to 36 in deep, fits a 36 in gate at 35.8 in wide, and leaves spoil in a row beside the cut. The first few feet against the foundation are often hand work because the trencher cannot start tight to a wall. If the route hugs the house, turns a corner, or crosses roots from foundation plantings, the Bobcat E10 is the better tool: it retracts to 28 in for the side yard, digs with an 8 in bucket, and places spoil out of the way. Dig from the outlet back toward the house so the trench drains while you work, and check the fall as you go. Follow the pipe manufacturer and local building department for depth.

Trencher 6 in x 36 in, or Bobcat E10 with the 8 in bucket.

Connect, test, backfill and restore

Connect the downspout adapter, run the pipe on a continuous fall to the outlet, and test it with a hose before you backfill. Water should come out the far end within a few seconds and the line should drain empty after you shut off. Backfill in lifts and compact each one; in a 6 in trench that is a hand tamper, in a wider E10 trench the plate compactor fits once the pipe is covered. Put the sod back or seed. Reset the grade at the wall so the soil slopes away from the house, which was probably part of the original problem.

Plate compactor for a wider trench; hand tamper for the trencher cut.

Water pooling in your yard: what to investigate first

What done looks like

  • In the next storm the splash block is gone, the base of the downspout is dry, and water comes out at the emitter or the ditch and keeps going. The soil against the foundation stays firm instead of turning to mud. The trench line over the lawn does not show as a dip.
  • Check the outlet a few times in the first year, especially after leaves drop and after the first freeze. A pop-up emitter buried in leaves or frozen shut backs the whole line up to the gutter.

Mistakes we see on return

  • Burying the line with a hump in it, so water sits in the pipe and the first hard freeze splits it. Tying the downspout into a French drain that was meant for groundwater, which floods it in a storm. Running the line to an outlet that is level with the downspout base, so it never fully drains. And starting the trencher inches from the foundation, which risks the footing and anything that runs along the wall.
  • On the equipment side: booking the trencher for a route with a 90 degree turn and shrub roots, when the E10 would have done it in the same time with less fighting.

When to call someone

  • Water inside the basement or a damp foundation wall is more than a downspout problem, and a foundation or waterproofing contractor should look before you dig along that wall. If the only outlet is a public storm sewer, the township or county decides whether and how you connect. If you find a footing drain, a sewer lateral or anything you did not expect while digging, stop and get it identified before continuing.

Before you book, check the site.

Measure the side yard

Side yards between a house and a fence are the narrowest point on most lots. The trencher is 35.8 in wide. The E10 retracts to 28 in to get through and extends to 43 in to work. Measure the clear opening and the narrowest point along the wall, including AC units and meters.

Check what is along the wall

Gas meter, electric service, hose bibs, AC lines, window wells, footing drains and foundation plantings. Mark them. Decide where the machine can start the cut and where the first stretch is hand work.

Bring the numbers

Length of the run, drop from the downspout base to the outlet, and how many downspouts tie in. These decide machine, pipe and how long you need it.

Machine widths, from our product pages

Width is the machine body. The E10 needs 43 in to work once it is through the narrow point. If you are a few inches short, pulling one fence panel is often easier than hand digging the whole run.

Bobcat E10 mini excavator — 28 in retracted / 43 in extended

Trencher 6 in x 36 in — 35.8 in

Before ground disturbance: — contact MISS DIG 811 at least three business days before digging. Services enter the house along the wall you are about to trench beside. MISS DIG does not mark private lines.

Your downspout extension checklist

Save these details before you request equipment.

  • Which downspouts cause the pooling (watched during a rain)
  • Gutters cleaned and checked for sags
  • Outlet location, drop from downspout base, and permission to discharge there
  • Route marked; meters, AC, window wells and plantings noted
  • Narrowest point along the side yard measured
  • Pipe depth and type from the manufacturer and building department
  • MISS DIG 811 ticket date
  • Delivery location and preferred dates

Let's match the machine to your job.

Tell us what you're working on. Our Hamburg team serves Southeast Michigan, seven days a week.

(810) 231-7368

Explore equipment for this guide

Questions before you rent

Trencher or E10 for a downspout line?

Trencher for a straight run from near the house out across open lawn, in soil without big roots or rock. It cuts a clean 6 in slot and the spoil goes right back in. E10 when the route runs tight along the foundation, turns a corner, crosses shrub roots, or has to go through a side yard under 36 in. The E10 also sets spoil where you want it instead of in a row on the lawn. For most single downspouts the trencher is the faster pick; for a line that collects several downspouts along a wall, the E10 earns its place.

How deep does the line need to be?

Ask the pipe manufacturer and your local building department; they set it, not us. The trencher reaches 36 in, which covers what most downspout lines call for. Frost depth in most of southeast Michigan is about 42 in, but a downspout line is designed to drain empty rather than to sit below frost, which is why the continuous fall matters more than the depth. If your spec does take the line past 36 in, it becomes an excavator trench.

Can I tie the downspout into my French drain or sump line?

Keep them separate unless a drainage contractor designed them together. A French drain is sized for groundwater seeping in slowly. A downspout dumps a large volume in minutes during a storm and can overwhelm it, pushing water back into the soil the drain was meant to dry. Sump discharge has the same issue in reverse. One pipe per job, each with its own outlet or a trunk sized for both.

Do I really need MISS DIG for a shallow trench next to my house?

Yes, and this is the trench where it matters most. Gas, electric, cable, phone, the water service and the sewer lateral all enter the house along a wall, often shallow. Michigan law requires contacting MISS DIG 811 at least three business days before digging, and it is free. Private lines such as irrigation, landscape lighting and a line to a detached garage are not marked by MISS DIG; find those yourself or with a private locator.

Can I tow the trencher myself?

The trencher rides on our 5x10 utility trailer with a 2 in ball, and most pickups and many SUVs handle it; we load it and check your hitch and lights at the yard. The E10 rides on the 16 ft equipment trailer with a 2 5/16 in ball and a truck rated for the load, confirmed at the counter. Delivery runs seven days a week on our trucks, priced by drive time from Hamburg: $85 round trip within 45 minutes, $125 at 46 to 75 minutes, and a quote beyond that. The fee is confirmed at checkout.