Refinishing hardwood floors: planning the equipment and sequence

The order of work, which sander does each step, and what to check before you book.

The refinish, in order

Each stage names the Ward's machine that does it. Skipping the first stage is how floors get ruined.

The week rate covers 3 to 7 days. A refinish with several coats and dry time in between almost always runs past a single day, so plan the booking around the finish schedule, not the sanding.

Confirm the floor can take a sanding

Solid hardwood with enough wear layer left can be sanded. Engineered flooring with a thin veneer, badly cupped boards, exposed nail heads and floors that have already been sanded several times may not survive another full pass. Pull a floor register or look at a stair nosing to see board thickness. If you are not sure what you have, stop here and read our checklist on whether a floor can be sanded.

No machine yet. A tape, a flashlight and a flat screwdriver for a heat register.

Empty the room and set nails

Everything comes out, including rugs, furniture and base shoe if you plan to sand to the wall. Set every nail or staple below the surface; a drum or orbital abrasive that hits a nail head is finished. Vacuum, then check the floor for old carpet tack strips and paint drips. Mask doorways and HVAC registers so dust stays in the room.

Hand tools. A 24 in high-volume fan in a window helps clear dust between passes.

Sand the field with the drum or orbital sander

The main machine does the open floor. The drum sander takes the floor to bare wood fast, and it digs a trough if you stop moving while the drum is down. The orbital sander is slower and forgiving; it will not gouge if you pause. Either way, work coarse to fine, with the floor fully covered at each step before you move finer. Keep the cord behind you and the machine moving.

Drum sander (belt-style, 8 in drum) for experienced users and heavy old finish; orbital sander (12 x 18) for first-timers and lighter resanding.

Sand walls, corners and stairs with the edger

Neither main machine reaches the last several inches at a wall or into a closet. The edger finishes that band at each grit, matching the main machine so the field and the edge look the same under finish. Inside corners and stair treads are hand work after the edger.

Edging sander (7 in, 30 lb). Rent it with either main machine.

Screen between finish coats

After the first coat of finish dries, a light pass with a screen on the orbital sander knocks down raised grain and dust nibs so the next coat lays flat. Vacuum and tack the floor afterward. Follow the finish manufacturer's instructions for recoat windows; this guide does not pick a finish.

Orbital sander with a screen. If you used the drum sander for the main pass, add the orbital for this step.

Move air while the finish cures

Fans move air across the floor and out of the room, which is what most finishes want during drying. Fans do not remove moisture from the air, and Ward's does not rent dehumidifiers, so a humid basement or a wet week in Michigan means longer dry times. Keep foot traffic off until the manufacturer's cure time has passed.

24 in high-volume fan or carpet air mover, positioned to pull air out a window, not blow dust onto wet finish.

Common mistakes we hear about at the counter

  • Stopping with the drum down. The drum sander cuts whenever it touches wood. Lower it as you start walking and lift it before you stop; a two-second pause leaves a dip you will see under finish.
  • Skipping grits. Jumping from coarse straight to fine leaves scratches the fine paper cannot remove, and they show up the moment finish goes on. Cover the whole floor at each step.
  • Forgetting the edger until the end. Edge at each grit as you go. An edge finished at one grit next to a field finished at another reads as a halo around the room.

When to call a flooring professional instead

  • Engineered floors with a veneer too thin to sand, floors with water damage or active cupping, parquet and herringbone where the grain changes direction every few inches, and floors in homes old enough that the existing finish or adhesive may contain lead or asbestos are jobs for a flooring contractor or an abatement firm. Test suspect materials before you disturb them.
  • If a floor just looks dull and the finish is intact, you may not need a full sanding at all. A screen and recoat with the orbital sander is a much smaller project. Call and describe what you see.

Before you book, check the room

Power

These sanders run on household power, but a long run of thin extension cord starves the motor. Confirm outlet and cord requirements for the machine you are booking when you reserve.

Getting the machine in

The drum and orbital sanders each weigh about 115 lb. Plan two people for stairs and for loading. They ride in a pickup or SUV; the edger is a one-hand carry.

Measure the floor

Square footage, number of rooms, number of closets and stair treads. Closets and stairs are edger and hand time, and that is often more than the open floor.

Your project checklist

Save these details before you request equipment.

  • Floor type confirmed: solid hardwood, and roughly how thick above the tongue
  • Square footage, rooms, closets and stair treads
  • Nails and staples set; tack strips and base shoe removed
  • Finish product chosen, with its recoat and cure times
  • Which main machine: drum or orbital, plus the edger
  • Fans and a window for exhaust
  • Pickup or delivery, and dates that cover the finish schedule

Let's match the machine to your job.

Tell us what you're working on. Our Hamburg team serves Southeast Michigan, seven days a week.

(810) 231-7368

Explore equipment for this guide

Questions before you rent

Drum sander or orbital for my first floor?

Most first-timers do better with the orbital. It takes longer to get to bare wood, but it does not gouge when you hesitate, and you will use it again to screen between coats. The drum sander is the right tool when there is thick old finish, when the floor is uneven, or when you have run one before. Our comparison guide goes deeper on the trade-off. Either one needs the edger alongside it.

Do I need the edger if I rent the orbital?

Yes. The orbital leaves a band along every wall and cannot get into closets, under toe kicks or onto stair treads. The edger finishes those areas at each grit so they match the field. Without it, the perimeter of the room keeps its old finish and the difference is obvious under new coats.

How long should I book the sanders for?

Long enough to sand, edge, vacuum, apply the first coat, let it dry, screen and recoat. That schedule is set by your finish product, not by us. Rental time is charged for the time the machine is out, including weekends, and the week rate covers 3 to 7 days, so a multi-day refinish usually fits best in a week booking. Keep it longer than planned and the extra time is prorated, never more than the next full period.

Will fans dry the finish faster?

Fans move air, which is what most finishes want while they dry, and they clear solvent odor out of the room. They do not remove moisture from the air. On a humid day or in a damp basement, expect dry times to stretch regardless of airflow. Ward's does not rent dehumidifiers. Aim the fan to pull air out a window rather than blowing across wet finish, which stirs dust onto it.

Can I pick these up in my car?

The drum and orbital sanders each weigh about 115 lb and ride in a pickup bed or an SUV with the seats down; bring a second person to lift. The edger is 30 lb. Delivery is also available seven days a week, priced by drive time from Hamburg: $85 round trip within 45 minutes for a truck load, confirmed at checkout.