If a tree came down this fall, or you finally had a dead one taken out, the stump is the part that gets left for later. Later gets harder once the ground freezes: a stump that is easy to grind in late October is a frozen, awkward job in January, and in spring it sits right where you want to mow or plant.
Fall is a good window: the tree work is done, the leaves are off, and the ground is still workable. The question we hear at the counter is not whether to remove it. It is how: grind it, or dig it out?
Grinding vs. Digging: What Each One Actually Does
Grinding chews the stump down below ground level and leaves the roots to break down underground. You are left with grindings and a shallow filled area you can use again, and nothing big to haul away.
Digging it out removes the stump and the root ball completely. That sounds cleaner, and sometimes it is the right call, but it leaves a bigger hole, tears up a wider area, and leaves you with a heavy root ball that still has to go somewhere.
When Grinding Is the Right Answer
For most yard stumps, grinding is the practical choice:
- The stump is in lawn, a landscape bed, or a fenced backyard
- You want to mow, plant grass, or put a smaller planting back over it
- You do not need the ground opened up for anything else
- Access is tight and a bigger machine would tear up more than it fixes
Grinding below grade matters. A stump ground only flush with the surface is still in the way of mower blades and new roots, and it keeps sprouting shoots around the edge.
When Digging It Out Makes Sense
Choose the dig-out when the stump and its roots are physically in the way of work that has to happen in that exact spot: a footing, a foundation or addition, a new driveway base, or a trench line that has to run straight through it. In those cases the roots have to go, not just the visible stump.
Digging is also reasonable if a mini excavator is already on site for other work. If it would come out just for one ordinary yard stump, grinding is almost always simpler: less digging, less backfill, less lawn to repair, and no root ball to haul.
The Machine We Send Out for This
Our Vermeer SC30TX tracked stump grinder is built for exactly the backyard case. It is a walk-behind tracked unit, 35 inches wide, so it fits through a standard 36-inch gate opening. The two tracks are controlled individually and it turns in its own footprint, which helps you line up on a stump without extra passes across the lawn. Rubber tracks are also easier on soft ground.
It cuts up to 12 inches below grade and 25 inches above it, so you do not have to saw a tall stump flush before you start. It runs a 25-hp Kohler engine with a Yellow Jacket cutter system, and its AutoSweep feature watches engine speed and adjusts the sweep rate, which keeps a first-time operator from taking too big a bite at once. It does need to travel on a trailer: we can deliver it, or set you up with a trailer for pickup.
See it alongside the chippers and splitters in our chippers, stump grinders and splitters section. If the tree work left brush too, pairing grinding and chipping into one weekend is common.
How to Grind a Stump, Step by Step
1. Call before you grind. You are working below grade, so have underground utilities marked first. In Michigan that is MISS DIG 811. Do not skip it because the stump looks like it is in open lawn.
2. Cut the stump low and clear the base. Saw it down low, then rake back soil, stones, and mulch. Rocks hidden at the base are hard on cutter teeth and can be thrown.
3. Check for surprises. Old fence wire, edging, and hardware grow into trees over the years. Look the stump over before the wheel touches it.
4. Work across the face in sweeps. Cut in passes across the stump, working down a little at a time instead of plunging straight in. Stay behind the machine and wear eye protection.
5. Go below grade, then chase the edge. Work to the depth you need and widen slightly past the stump’s edge so surface roots and sprout points go with it.
6. Fill like it will settle, because it will. Rake the grindings back into the hole, mound them slightly high, and top up with soil after it settles.
A Practical Stump Checklist
- Measure the stump across at its widest, flare included, and count how many you have
- Measure your gate or tightest access point before you reserve
- Have utilities marked through MISS DIG 811
- Cut the stump low, and clear rocks and soil from the base
- Decide where the grindings go: in the hole, in beds, or hauled out
- Have soil on hand for the top-up after settling
- Plan the trailer or delivery when you book, not the morning of
Mistakes We See
Grinding too shallow is the big one: it looks finished, then the spot will not take a planting, keeps sprouting, or catches a mower. Burning is the other one: a stump burns slowly and unevenly, often just charring on top while staying solid underneath, and it can smolder in the roots far longer than you expect.
Ready to Get That Stump Gone Before Winter?
Call Ward’s Equipment Rental at 810-231-7368. Tell us how wide the stump is, how many you have, and how wide your gate is, and we will help you decide honestly whether grinding is the right call or whether your job is one of the dig-out cases. You can also browse the stump grinders, chippers, and splitters linked above before you call.
