Posted on — Leave a comment

Heating a Job Site in Cold Weather: How to Size a Forced-Air Heater

By mid-November in Michigan, cold stops being an inconvenience and starts costing days. Fresh concrete cures slowly and can be damaged if it freezes early. Frozen ground fights every bucket. Paint, adhesive and joint compound sit there and refuse to set up, and a crew working in an unheated shell spends half its energy just staying warm. A forced-air heater is the simplest fix on most jobs, but it only helps if it is sized for the space and run safely. Here is how we help customers pick one.

Start With the Space, Not the Heater

The number that matters is the size of the space and how closed up it is. Heater ratings assume a closed building, and they are a good starting point: our smaller heater is rated for up to 1,875 square feet, and the larger one for up to 4,750 square feet. An open pole barn, a house with no windows in yet, or a drafty shop loses heat fast, so if your building is open or poorly sealed, size up rather than down. A heater that is a little big cycles comfortably. One that is too small runs flat out all day and never catches up, and the job stays cold anyway.

Ceiling height counts too. A 1,800-square-foot garage with a 9-foot ceiling is a very different job from the same footprint with a 16-foot peak, because you are heating the air volume, not the floor. When you call, tell us the length, width and ceiling height, and whether the building is closed in. That is enough for us to size it with you.

The Two Heaters We Rent

Our heating rentals are two Mi-T-M forced-air heaters, and between them they cover most winter work we see.

The 75,000 BTU heater is the garage and workshop unit. It heats up to 1,875 square feet, weighs just 28 pounds, and is easy to carry from room to room or spot to spot. It is the right pick for a two- or three-car garage, a small addition, a workshop, or thawing pipes and equipment in a contained area. It starts at $65.

The 190,000 BTU heater is the big-building unit, rated for up to 4,750 square feet. At 62 pounds it is still a one-person move with care, and it is the one crews take for barns, pole buildings, and houses or commercial spaces under construction that are not closed in yet. It starts at $125.

Fuel, Power and Run Time

Both heaters burn kerosene, diesel or fuel oil — never gasoline. Kerosene is the cleanest-burning choice for enclosed work areas. The 75,000 BTU heater holds 5.3 gallons and burns about 0.55 gallons an hour, so a tank lasts roughly 9.5 hours. The 190,000 BTU heater holds 13.2 gallons and burns about 1.37 gallons an hour, for roughly 10 hours a tank. In plain terms, a full tank in the morning gets you through a workday, and refueling is a five-minute job with the heater off and cool.

Both also need a standard 120-volt grounded outlet to run the fan and burner, so plan a cord to wherever the heater will sit. Run time itself is simple with a rental: you pay for the time the heater is out, not the hours it runs, and fuel is billed at our cost with no markup. Run it as much as the job needs.

Ventilation and Clearance Are Not Optional

Forced-air heaters burn fuel in the space and exhaust into it, which is why they belong in garages, shops, barns and buildings under construction — never in a house or room anyone is living or sleeping in. The manufacturer’s guidance is at least 3 square feet of outside-air opening for every 45,000 BTU of heater rating. That works out to about 5 square feet of opening for the 75,000 BTU heater — a garage door raised partway gets you there — and about 13 square feet for the 190,000 BTU heater.

Keep at least 3 feet clear above and beside the heater and 10 feet clear in front of it, and never block the air intake at the back. Set it on a level spot where it will not be bumped, and keep fuel stored away from the heat. Ten minutes of setup attention is all it takes, and it is the difference between a heater that is a tool and one that is a hazard.

Jobs That Commonly Need Heat

The rentals we see most in cold weather are a winter concrete pour that needs warm air while it cures, a remodel or addition where finish work cannot start in the cold, a barn or shop where equipment and materials need to stay above freezing, and thawing a work area or frozen ground cover before digging. If your job is on that list, the deciding questions are just the size of the space, how open it is, and how many days you need to hold the temperature.

Cold-Weather Heating Checklist

  • Measure the space: length, width and ceiling height
  • Note how closed in it is — windows and doors in, or still open
  • Pick fuel: kerosene for the cleanest burn in enclosed areas
  • Plan a grounded 120-volt outlet within cord reach of the heater spot
  • Plan the ventilation opening before the heater arrives
  • Clear 3 feet around the heater and 10 feet in front of it
  • Decide how many days you need to hold heat, not just warm up once

Not sure which size your building points to? Call or text Ward’s Equipment Rental in Hamburg at 810-231-7368 with the size of the space and how open it is, and we will size it with you — or browse the heating rentals and tell us about the job when you request one.

Posted on — Leave a comment

Telehandler Reach Planning: Pick the Machine by the Lift at the Far End

The most common telehandler mistake happens before the machine ever leaves the yard: picking it by the big number on the side. A 6,000 lb machine does not lift 6,000 lb everywhere. It lifts that close in, with the boom down. Stretch the boom out to set a truss or land a pallet in the middle of a building, and the same machine may be good for a fifth of that. Plan the lift at the far end — how high, how far out, and how heavy that farthest pick actually is — and the right machine usually picks itself.

Start With Three Numbers, Not One

Before you call, work out three things about your heaviest, hardest lift. First, the height: where does the load have to end up, not how tall is the building? Second, the forward reach: how far from the front tires will the load be when you set it? A machine parked outside a wall, reaching into the middle of a building, can need most of its reach even on a modest job. Third, the weight at that spot, including the pallet, rigging and anything hanging from a hook.

Write those three numbers down. They matter more than the model name, and they are exactly what we will ask about when you book.

What Our Four SkyTraks Actually Do

Our telehandler fleet runs from 6,000 to 10,000 lb and 34 to 42 feet of lift, and the differences are mostly in what each machine keeps at full stretch.

The SkyTrak 6034 is the compact one: 6,000 lb capacity, 34 ft 5 in of lift and 23 ft 2 in of forward reach, with about 1,000 lb left at full reach. At 14,500 lb and 7 ft 11 in wide, it is the easiest on tight residential lots, and it covers most one- and two-story houses, garages and additions. Day rates start at $445 for up to 24 hours.

The SkyTrak 6042 keeps the same 6,000 lb class but lifts 42 ft 4 in and reaches 29 ft 6 in, with about 1,200 lb at full reach. That extra reach is why it is the pole barn and truss-setting machine, and the one most framers and roofers ask for. It starts at $495 for up to 24 hours.

The SkyTrak 8042 lifts the same 42 ft 4 in and reaches the same 29 ft 6 in, but carries 8,000 lb close in, 6,000 lb at full height and 1,600 lb at full reach. That is the step up for heavier trusses, beams and full pallets. It starts at $545 for up to 24 hours. The SkyTrak 10042 is the heavy end: 10,000 lb capacity, 42 ft 1 in of lift, and — this is the number that matters — still 6,000 lb at full height and at full reach. Its forward reach is a little shorter at 26 ft 9 in, so it trades a few feet of reach for a lot of strength at the far end, which is the right trade for steel, block and heavy pallets placed well out from the machine. It starts at $645 for up to 24 hours.

Whichever machine you take, the load chart in the cab is the final word on a given lift. Operators need to be trained to run a telehandler, and every pick should be planned from that chart, not from the headline capacity.

Attachments Change the Math

Three attachments do most of the extra work on our telehandlers, and each one changes what the machine can lift, so plan them in from the start rather than adding them as an afterthought. The 15 ft truss boom adds reach with a hook for setting trusses and long lumber or steel over a wall; it is listed at 2,000 lb, rents for $100 alongside a telehandler, and the telehandler’s own load chart still governs. The adjustable jib, which runs from 7 to 12 ft, hangs beams, pipe and precast from a hook so they can be lowered into place. The fork-mounted work platform lifts a crew and tools — 1,000 lb listed capacity, people and tools combined — for short work at the eaves when the machine is already on site, with fall protection tied off to the platform required.

Ground, Access and Delivery

Reach planning also means planning where the machine will sit. These are four-wheel-drive diesel machines built for rough ground, but they are heavy: from 14,500 lb for the 6034 up to 26,600 lb for the 10042, and from 7 ft 11 in to 8 ft 6 in wide. In late fall, think about soft lawns, fresh driveways and mud between the road and the building, and give the machine a firm, level spot to work from. If the only good spot is farther from the building, that distance comes straight out of your reach — another reason to measure the farthest set before you book.

Telehandlers go out on our own trucks. Round-trip delivery is $350 within 45 minutes’ drive of our Hamburg yard and $450 for 46 to 75 minutes. Run hours are unlimited; you pay for the time the machine is out, not the hours on the meter.

Telehandler Planning Checklist

  • Height of the highest set, measured to where the load lands
  • Forward reach from the front tires to that same set
  • Weight of the heaviest load at full reach, pallet and rigging included
  • Attachment needed: forks, truss boom, jib or work platform
  • A firm, level working spot, with the width and ground to get there
  • A trained operator, and a plan to check each big pick against the load chart

Not sure which machine your farthest lift points to? Call or text Ward’s Equipment Rental in Hamburg at 810-231-7368 with your height, reach and load weight and we will size it with you, or browse the telehandlers and tell us the job when you request one.

Posted on — Leave a comment

Splitting Firewood Before Winter: How to Get Through a Pile of Rounds in One Weekend

If you heat with wood, or just like a real fire all winter, November is when the pile of rounds in the yard stops being a someday project. Split wood needs time stacked and drying before it burns well, and every week those rounds sit whole is a week they are not seasoning. The good news: with a hydraulic splitter, a job that looks like a month of weekends with a maul turns into one solid day.

Why Split Now Instead of Later

Wood dries from the cut surfaces, and a whole round has very little surface compared to a split piece. Splitting opens the wood up so air can get to it. Split and stack your firewood now and it will burn noticeably better this winter than rounds split in January, and far better than rounds left whole until you need them. Splitting green wood is also easier work than splitting rounds that have sat and hardened for a year.

Cut your rounds to the length your stove or fireplace takes before you start. Sixteen inches is the common length, but measure your firebox rather than guessing. Consistent lengths stack tighter, dry more evenly, and save you from re-cutting pieces at the woodpile in February.

Maul or Hydraulic Splitter?

A maul is fine for a handful of straight-grained pieces you split for fun on a Saturday morning. It stops being fine when you are looking at a full cord or more, knotty oak or maple, or rounds much over a foot across. That is where most people stall out, and the pile sits until spring.

Our Iron & Oak 30-ton log splitter works through knotty, stringy and oversized rounds that would turn a maul session into a wrestling match. Thirty tons of force does not care about a knot the way your shoulders do. For most homeowners, the honest math is simple: one day with a splitter equals several weekends of swinging, with a lot less wear on your back.

How a Splitting Day Goes

Set the splitter up on level ground close to the round pile, with your stacking area or trailer on the other side so split pieces move in one direction and nobody is carrying wood back and forth. Stage a good supply of rounds within arm’s reach before you start the engine.

Two people make the day go twice as fast: one runs the splitter, the other stages rounds and carries split wood to the stack. Swap jobs every so often. Keep hands clear of the wedge and the log while the ram is moving, wear gloves, eye protection and sturdy boots, and never reach across the beam to steady a piece. Work at a pace you can hold all day rather than racing the first hour and fading by lunch.

Stacking So It Actually Dries

Splitting is only half the job. Stack the wood off the ground on pallets or rails, bark side up where you can, with a little air space between rows. A single row deep in a sunny, breezy spot dries fastest. Cover the top of the stack to shed rain and snow, but leave the sides open so air can move through. A full cord, stacked, is 4 feet high by 4 feet wide by 8 feet long; knowing that helps you plan how much space the finished pile needs before you start.

What the Rental Looks Like

The log splitter rents for $60 for 1 to 4 hours, $90 for a day, $325 for a week and $900 for 4 weeks. For most yards, the day rate is the sweet spot: pick it up in the morning, split at a steady pace, and bring it back with the whole pile done. The splitter tows behind your vehicle, and we will confirm your hitch and towing setup at the counter when you pick up. If you would rather not tow, round-trip delivery for towable equipment like the splitter is $125 within 45 minutes of our Hamburg store.

Taking down or trimming trees to get those rounds in the first place? The same chippers, stump grinders and splitters category covers the rest of the cleanup: a chipper shredder turns the limbs into mulch, and a stump grinder takes the stump below grade so nothing is left sticking out of the yard.

Firewood Splitting Checklist

  • Rounds cut to your stove’s length, staged in one place
  • Level spot for the splitter, stack or trailer set up on the far side
  • Pallets or rails ready so split wood goes straight onto the stack
  • Gloves, eye protection and sturdy boots for everyone helping
  • A second person if you can get one — staging and stacking is half the work
  • Tarp ready to cover the top of the finished stack

Got a pile of rounds waiting on you? Call or text Ward’s Equipment Rental in Hamburg at 810-231-7368 and we will set you up with the log splitter for the day that fits your schedule, or browse the chippers, stump grinders and splitters to plan the whole cleanup at once.

Posted on

Our Rental Rates Aren’t Going Up

Good news for anyone planning a project: our rental rates aren’t going up. No increases are planned, and the rates you see on our website are the rates you pay.

What that means when you rent from Ward’s

  • Published rates. Every machine on our site shows its half-day (1–4 hours), day (4.5–24 hours), week and 4-week rate. No “call for pricing.”
  • Delivery from $85 round trip for skid steers, mini excavators and most equipment within 45 minutes of our Hamburg yard, on our own trucks with our own drivers. See all delivery rates.
  • No surprise fees. Rent, delivery and sales tax up front. Fuel is billed at our cost with no markup, and we don’t bill by the hour meter.
  • Open 7 days. We rent, deliver and pick up seven days a week, so weekend projects don’t have to wait for Monday.

Why we can hold the line

We own our fleet, do most repairs in-house, and run our own delivery trucks. There’s no marketplace or middleman taking a cut, so we can keep rates steady instead of passing along increases.

Browse all rental equipment, see delivery fees for your town, or call or text us at (810) 231-7368.

— Andy Ward, owner

Posted on

Pole Barn Site Prep: Grading, Post Holes and Getting the Trusses Up

A pole barn goes up fast once the posts are in, but the site work decides how it holds up for the next 30 years. A flat, well-drained pad and post holes below the frost line prevent most of the problems people run into later.

Permits and Utilities First

Most townships in Livingston County and the surrounding area need a permit for an accessory building, and they’ll have setback and size rules. Get that sorted before you rent anything. Then call MISS DIG (811) at least three business days before you dig so buried lines get marked.

Clearing the Site

Take out brush, small trees and stumps first. A brush chipper and stump grinder clear a wooded spot quickly. A tracked skid steer with a root grapple handles the debris.

Grading the Pad

Strip the topsoil and organic material from the footprint plus a few feet around it, since topsoil settles and holds water. Then build the pad up with compacted fill and stone so it sits a little higher than the ground around it, and grade the area so water runs away from the building on all sides.

A tracked skid steer like the Bobcat T66-2 or Kubota SVL65-2 is the right machine here. Tracks float on soft ground and handle the cutting, filling and fine grading. Compact the stone with a ride-on roller or plate compactor before you lay out the posts.

Post Holes

Pole barn posts need to go below the frost line, which is about 42 inches in most of Southeast Michigan, and many builders go 4 ft or deeper. Follow your building plans and permit for depth and hole size. A skid steer with a hydraulic auger drills these holes in a fraction of the time of a hand auger, and keeps them plumb.

Lay the building out with batter boards and string, check that the diagonals match so it’s square, and mark every post location before you drill.

Setting Posts and Lifting Trusses

Once the posts are set and braced, a telehandler is the safest way to get trusses and roof steel up. The SkyTrak 6042 reaches 42 ft and lifts 6,000 lb, which covers most residential pole barns. For heavy truss packages, use the 8042 or 10042. Add a truss boom attachment to set trusses one at a time. Telehandlers are delivery-only for almost every customer, and we drop them at your site.

Equipment Checklist

  • Tracked skid steer with bucket, root grapple and auger
  • Chipper and stump grinder if the site is wooded
  • Plate compactor or ride-on roller for the pad
  • Telehandler with truss boom for the roof
  • Dump trailer for hauling spoils

Call us at (810) 231-7368 and we’ll help you plan the rental around your build schedule. Weekly and 4-week rates usually make the most sense for a pole barn.

Posted on

How to Build a Paver Patio Base That Won’t Sink

When a paver patio sinks, heaves or grows ruts after a couple of winters, the pavers are almost never the problem. The base is. Getting the excavation, base stone and compaction right is most of the job, and it’s the part you can’t fix later without pulling everything up.

How Deep to Dig

For a walking patio, plan on about 4 to 6 inches of compacted base stone, an inch of sand or fine bedding, plus the thickness of the paver. That usually means digging 7 to 9 inches below the finished height. Go deeper where you have soft clay, poor drainage, or anywhere a vehicle might drive.

Dig out a little past the edges of the patio, about 6 inches all around, so the base supports the edge restraint and the outer row of pavers.

Slope It Away From the House

Build in a slope of about 1/8 to 1/4 inch per foot away from the house so water runs off instead of pooling. Set the slope in the dirt when you dig, then follow it with the base. Don’t try to make it up in the sand layer.

Compact in Layers

This is where most DIY patios go wrong. Compact the soil at the bottom of the hole first. Then add base stone 2 to 3 inches at a time, dampen it, and run a plate compactor over each layer before adding the next. Dumping all 6 inches and compacting once leaves the bottom loose, and that’s what sinks later.

The Equipment That Saves the Most Time

  • Digging: a mini excavator or the MT100 stand-on loader takes the sod and dirt out in hours instead of days. The MT100 fits through backyard gates.
  • Moving stone: the same loader moves base stone from the driveway to the patio. A dump trailer hauls the dirt away.
  • Compacting: the Wacker Neuson plate compactor handles base stone and sets the pavers at the end.
  • Cutting: a brick and paver saw makes clean cuts on the edges and around steps.

Finishing

Screed the bedding sand flat, lay the pavers, install the edge restraint, sweep in joint sand, and run the compactor over the top (with a pad if your pavers call for it) to lock everything in. Sweep in more joint sand and you’re done.

Call MISS DIG (811) before you dig, especially near the house where gas and electric lines come in. Questions on what to rent? Call us at (810) 231-7368.

Posted on

How to Dig Fence Post Holes: Hand Auger, Stand-On Loader or Skid Steer?

Digging post holes by hand is fine for three or four posts. For a fence line, it’s the slowest and hardest part of the job, and Michigan clay and stones make it worse. The right auger turns a weekend of digging into an afternoon.

How Deep Should Fence Posts Go?

A common rule is to bury about a third of the post. For a 6 ft privacy fence on an 8 ft post, that’s roughly 2.5 to 3 ft deep. Corner, end and gate posts carry the most load, so set those deeper. In Southeast Michigan, frost can reach about 42 inches, and posts set shallower than the frost line can heave over a few winters. Check with your township, since some have their own fence rules and permit requirements.

Make the hole about three times the width of the post: roughly 10 to 12 inches across for a 4×4. Put a few inches of gravel in the bottom for drainage before you set the post.

Call MISS DIG First

Call 811 or file online with MISS DIG at least three business days before you dig. They’ll mark buried gas, electric and cable lines for free. A fence line is exactly where a lot of buried service lines run.

Which Auger to Rent

Handheld auger. A handheld post hole auger works for a short run, a few deck footings, or a spot a machine can’t reach. It still takes muscle, and rocks or roots will stop it.

Stand-on loader with auger. The Bobcat MT100 with a hydraulic auger is the sweet spot for most backyard fences. It fits through a standard gate, drills a hole in seconds, and nobody is wrestling handles. The machine does the work, so the posts end up straight and the holes clean.

Full-size skid steer with auger. For pasture fence, long property lines or pole barn posts, a tracked Bobcat with an auger has the power and reach for bigger, deeper holes in hard ground.

Tips for a Straight Fence

  • Set the corner and end posts first, then run a string line between them for the line posts.
  • Mark every hole with paint before you start drilling.
  • Brace each post plumb in two directions before the concrete or tamped gravel sets.
  • Slope the top of the concrete away from the post so water runs off.

Our machines with augers go out on our trailers if you have a truck rated to tow them, or we deliver. See our post hole augers or call (810) 231-7368.

Posted on

When to Aerate and Overseed Your Lawn in Southeast Michigan

Most lawns in Livingston and Washtenaw counties sit on heavy soil that packs down hard. Kids, dogs, mowers and a few years of foot traffic squeeze the air out of it, and the grass starts thinning no matter how much you water or fertilize. Core aeration fixes that, and overseeding right after is the cheapest way to thicken a tired lawn.

When to Do It

Our lawns are cool-season grass: Kentucky bluegrass, ryegrass and fescue. They grow hardest in cool weather, so the best window is late August through September. The soil is still warm enough for seed to germinate, the nights are cooler, and new grass has the whole fall to root in before winter. Weeds are also slowing down, so they don’t crowd out the new seed.

Spring works too. Mid-April through May is the second-best window. The catch: if you put down a crabgrass preventer in spring, it also stops grass seed from coming up. Pick one or the other, or wait until fall to seed.

Aerate or Dethatch?

Push a screwdriver into the lawn. If it fights you, the soil is compacted and you need to aerate. Now pull back the grass and look at the layer between the blades and the dirt. If there’s more than about half an inch of brown, spongy thatch, dethatch first so seed can reach the soil. Plenty of homeowners do both on the same weekend.

How to Aerate and Overseed

  1. Water first. Aerate a day after a good rain or a deep watering. Dry soil is too hard for the tines; soaked soil just smears.
  2. Flag sprinkler heads and shallow lines. The tines go a few inches deep and will crack a sprinkler head.
  3. Mow short. Drop the mower a notch or two so seed can reach the soil.
  4. Aerate in two directions. Make one pass, then a second at an angle. You want plugs every few inches.
  5. Leave the plugs. They break down in a week or two and put soil back on top.
  6. Seed right away. Spread seed while the holes are open. A broadcast spreader does it evenly.
  7. Keep it damp. Water lightly once or twice a day until the new grass is up, then back off to deeper, less frequent watering.

Which Machine to Rent

For a typical yard, the gas walk-behind core aerator is the right tool. It pulls real plugs instead of just poking holes. Plan on about an hour per quarter acre. If you have a lawn tractor and a big lot, the 40-inch tow-behind aerator and dethatcher cover ground much faster.

A lawn roller after seeding presses seed into good contact with the soil, and it’s handy in spring for flattening frost heave. If you’re starting over on a bare area, a sod cutter or tiller strips the old turf first.

Walk-behind aerators fit in most pickup beds, or we can deliver. Call us at (810) 231-7368 or reserve online.

Posted on

Stump Grinder vs. Digging It Out: How to Remove a Stump Before the Ground Freezes

If a tree came down this fall, or you finally had a dead one taken out, the stump is the part that gets left for later. Later gets harder once the ground freezes: a stump that is easy to grind in late October is a frozen, awkward job in January, and in spring it sits right where you want to mow or plant.

Fall is a good window: the tree work is done, the leaves are off, and the ground is still workable. The question we hear at the counter is not whether to remove it. It is how: grind it, or dig it out?

Grinding vs. Digging: What Each One Actually Does

Grinding chews the stump down below ground level and leaves the roots to break down underground. You are left with grindings and a shallow filled area you can use again, and nothing big to haul away.

Digging it out removes the stump and the root ball completely. That sounds cleaner, and sometimes it is the right call, but it leaves a bigger hole, tears up a wider area, and leaves you with a heavy root ball that still has to go somewhere.

When Grinding Is the Right Answer

For most yard stumps, grinding is the practical choice:

  • The stump is in lawn, a landscape bed, or a fenced backyard
  • You want to mow, plant grass, or put a smaller planting back over it
  • You do not need the ground opened up for anything else
  • Access is tight and a bigger machine would tear up more than it fixes

Grinding below grade matters. A stump ground only flush with the surface is still in the way of mower blades and new roots, and it keeps sprouting shoots around the edge.

When Digging It Out Makes Sense

Choose the dig-out when the stump and its roots are physically in the way of work that has to happen in that exact spot: a footing, a foundation or addition, a new driveway base, or a trench line that has to run straight through it. In those cases the roots have to go, not just the visible stump.

Digging is also reasonable if a mini excavator is already on site for other work. If it would come out just for one ordinary yard stump, grinding is almost always simpler: less digging, less backfill, less lawn to repair, and no root ball to haul.

The Machine We Send Out for This

Our Vermeer SC30TX tracked stump grinder is built for exactly the backyard case. It is a walk-behind tracked unit, 35 inches wide, so it fits through a standard 36-inch gate opening. The two tracks are controlled individually and it turns in its own footprint, which helps you line up on a stump without extra passes across the lawn. Rubber tracks are also easier on soft ground.

It cuts up to 12 inches below grade and 25 inches above it, so you do not have to saw a tall stump flush before you start. It runs a 25-hp Kohler engine with a Yellow Jacket cutter system, and its AutoSweep feature watches engine speed and adjusts the sweep rate, which keeps a first-time operator from taking too big a bite at once. It does need to travel on a trailer: we can deliver it, or set you up with a trailer for pickup.

See it alongside the chippers and splitters in our chippers, stump grinders and splitters section. If the tree work left brush too, pairing grinding and chipping into one weekend is common.

How to Grind a Stump, Step by Step

1. Call before you grind. You are working below grade, so have underground utilities marked first. In Michigan that is MISS DIG 811. Do not skip it because the stump looks like it is in open lawn.

2. Cut the stump low and clear the base. Saw it down low, then rake back soil, stones, and mulch. Rocks hidden at the base are hard on cutter teeth and can be thrown.

3. Check for surprises. Old fence wire, edging, and hardware grow into trees over the years. Look the stump over before the wheel touches it.

4. Work across the face in sweeps. Cut in passes across the stump, working down a little at a time instead of plunging straight in. Stay behind the machine and wear eye protection.

5. Go below grade, then chase the edge. Work to the depth you need and widen slightly past the stump’s edge so surface roots and sprout points go with it.

6. Fill like it will settle, because it will. Rake the grindings back into the hole, mound them slightly high, and top up with soil after it settles.

A Practical Stump Checklist

  • Measure the stump across at its widest, flare included, and count how many you have
  • Measure your gate or tightest access point before you reserve
  • Have utilities marked through MISS DIG 811
  • Cut the stump low, and clear rocks and soil from the base
  • Decide where the grindings go: in the hole, in beds, or hauled out
  • Have soil on hand for the top-up after settling
  • Plan the trailer or delivery when you book, not the morning of

Mistakes We See

Grinding too shallow is the big one: it looks finished, then the spot will not take a planting, keeps sprouting, or catches a mower. Burning is the other one: a stump burns slowly and unevenly, often just charring on top while staying solid underneath, and it can smolder in the roots far longer than you expect.

Ready to Get That Stump Gone Before Winter?

Call Ward’s Equipment Rental at 810-231-7368. Tell us how wide the stump is, how many you have, and how wide your gate is, and we will help you decide honestly whether grinding is the right call or whether your job is one of the dig-out cases. You can also browse the stump grinders, chippers, and splitters linked above before you call.

Posted on

How to Grade a Gravel Driveway Before Winter: Fix Potholes and Crown It Right

If you have a gravel driveway, you already know what winter does to it. Potholes fill with water, that water freezes and pushes the hole bigger, and the first time you plow or run a snowblower across it you catch every rut you meant to fix in October. Fall is the best window to grade it right: the gravel is still workable, the ground is not frozen, and a driveway shaped correctly now will shed meltwater all winter.

Why the Crown Matters More Than the Potholes

Most gravel driveway problems are really drainage problems. A driveway that is flat, or worse, low in the middle, holds water in the tire tracks. Traffic splashes that water out, taking fines and small stone with it, and a shallow dip becomes a pothole in a few weeks.

The fix is a slight crown: the center of the driveway sits a few inches higher than the edges, so water sheets off to the sides instead of sitting in the drive. When you grade, you are not just smoothing the surface. You are rebuilding that crown and pulling the stone that has migrated to the edges and the apron back where it belongs.

Do Not Just Fill the Holes

Dumping fresh gravel into a pothole without loosening the surface is the most common wasted weekend we hear about. The new stone has nothing to lock into, so it kicks out within a few passes and the hole comes right back.

Break up the surface first, including the bottom and edges of each pothole, then mix the old and new material together and reshape it. Compacted, interlocked gravel is what holds. Loose stone sitting on top of a hard pan does not.

The Equipment That Makes This a One-Day Job

For most driveways, the pairing that works is a skid steer with a bucket plus a soil conditioner, also called a Harley rake. The bucket moves material: fresh stone from a pile, gravel pulled back from the edges, and soil if you need to cut a high spot. The conditioner does the finish work.

Our compact stand-on skid loader soil conditioner is listed specifically for gravel driveway and parking lot maintenance. It has a 48-inch working width and a working depth of 0 to 2.5 inches, which is the right range for loosening a compacted gravel surface without digging up the base underneath. Its spiraled teeth windrow rocks and debris to the side as you go, and the float mount follows the shape of the drive while you adjust depth on the go.

It pairs with the Bobcat MT100 compact stand-on skid loader, a good fit for shorter drives and tight turnarounds. The MT100 is 35.6 inches wide, fits through a standard 36-inch fence opening, and has a 1,000-pound rated operating capacity.

For a long driveway or a job spreading several loads of fresh stone, step up to a full-size tracked machine like our Bobcat T66 tracked skid loader, which comes with a bucket or forks and is built for grading, backfilling, and material handling. You can compare both sizes in our earth moving equipment lineup.

How to Grade It, Step by Step

1. Walk it first. Note where water sits and where stone has washed off. If a ditch or culvert is blocked, fix that too, because a crowned driveway still needs somewhere for water to go.

2. Add stone before you grade if the drive is thin. If you can see dirt through the gravel in the tire tracks, grading alone will just mix dirt into the surface. Spread fresh gravel first, then grade it in.

3. Loosen the whole surface. Run the soil conditioner over the full drive, potholes included, deep enough to break up the compacted top layer. Make a second pass over the worst sections.

4. Pull material back to the center. Use the bucket and the conditioner to bring stone in from the edges and rebuild the crown as you shape each pass, working from one end to the other instead of spot-fixing.

5. Shape, then let it settle. A light rain after grading helps gravel settle and lock together. Avoid grading once the surface is frozen; at that point you are fighting the ground instead of shaping it.

A Practical Driveway Checklist

  • Walk the drive and mark potholes, low spots, and drainage problems
  • Check that ditches and the road edge will actually drain
  • Order fresh gravel ahead of time if the surface is thin or dirt is showing
  • Choose your machine size: stand-on for short or tight drives, full-size tracked for long drives
  • Add the soil conditioner attachment; a bucket alone will not loosen a compacted surface well
  • Grade on a dry day before the ground freezes
  • Rebuild the crown, do not just level the drive flat
  • Plan where windrowed rocks and debris will go when you finish

Mistakes That Bring the Potholes Back

Filling holes without loosening them, grading a driveway dead flat, and pulling stone so aggressively that you thin out the middle are the three we see most. The other one is waiting too long. Once the surface freezes hard, a fall grading job becomes a spring rebuilding job, usually with more stone to buy.

Done now, this is a one-day project for most driveways, and it pays you back every time you plow and every time spring melt runs off to the sides instead of down the tire tracks.

Ready to Get Your Driveway Ready for Winter?

Call Ward’s Equipment Rental at 810-231-7368. Tell us roughly how long your driveway is, whether you are adding fresh stone, and how tight the turnaround is, and we will help you match the skid steer and soil conditioner to the job. You can also browse the earth moving equipment linked above before you call.