By mid-November in Michigan, cold stops being an inconvenience and starts costing days. Fresh concrete cures slowly and can be damaged if it freezes early. Frozen ground fights every bucket. Paint, adhesive and joint compound sit there and refuse to set up, and a crew working in an unheated shell spends half its energy just staying warm. A forced-air heater is the simplest fix on most jobs, but it only helps if it is sized for the space and run safely. Here is how we help customers pick one.
Start With the Space, Not the Heater
The number that matters is the size of the space and how closed up it is. Heater ratings assume a closed building, and they are a good starting point: our smaller heater is rated for up to 1,875 square feet, and the larger one for up to 4,750 square feet. An open pole barn, a house with no windows in yet, or a drafty shop loses heat fast, so if your building is open or poorly sealed, size up rather than down. A heater that is a little big cycles comfortably. One that is too small runs flat out all day and never catches up, and the job stays cold anyway.
Ceiling height counts too. A 1,800-square-foot garage with a 9-foot ceiling is a very different job from the same footprint with a 16-foot peak, because you are heating the air volume, not the floor. When you call, tell us the length, width and ceiling height, and whether the building is closed in. That is enough for us to size it with you.
The Two Heaters We Rent
Our heating rentals are two Mi-T-M forced-air heaters, and between them they cover most winter work we see.
The 75,000 BTU heater is the garage and workshop unit. It heats up to 1,875 square feet, weighs just 28 pounds, and is easy to carry from room to room or spot to spot. It is the right pick for a two- or three-car garage, a small addition, a workshop, or thawing pipes and equipment in a contained area. It starts at $65.
The 190,000 BTU heater is the big-building unit, rated for up to 4,750 square feet. At 62 pounds it is still a one-person move with care, and it is the one crews take for barns, pole buildings, and houses or commercial spaces under construction that are not closed in yet. It starts at $125.
Fuel, Power and Run Time
Both heaters burn kerosene, diesel or fuel oil — never gasoline. Kerosene is the cleanest-burning choice for enclosed work areas. The 75,000 BTU heater holds 5.3 gallons and burns about 0.55 gallons an hour, so a tank lasts roughly 9.5 hours. The 190,000 BTU heater holds 13.2 gallons and burns about 1.37 gallons an hour, for roughly 10 hours a tank. In plain terms, a full tank in the morning gets you through a workday, and refueling is a five-minute job with the heater off and cool.
Both also need a standard 120-volt grounded outlet to run the fan and burner, so plan a cord to wherever the heater will sit. Run time itself is simple with a rental: you pay for the time the heater is out, not the hours it runs, and fuel is billed at our cost with no markup. Run it as much as the job needs.
Ventilation and Clearance Are Not Optional
Forced-air heaters burn fuel in the space and exhaust into it, which is why they belong in garages, shops, barns and buildings under construction — never in a house or room anyone is living or sleeping in. The manufacturer’s guidance is at least 3 square feet of outside-air opening for every 45,000 BTU of heater rating. That works out to about 5 square feet of opening for the 75,000 BTU heater — a garage door raised partway gets you there — and about 13 square feet for the 190,000 BTU heater.
Keep at least 3 feet clear above and beside the heater and 10 feet clear in front of it, and never block the air intake at the back. Set it on a level spot where it will not be bumped, and keep fuel stored away from the heat. Ten minutes of setup attention is all it takes, and it is the difference between a heater that is a tool and one that is a hazard.
Jobs That Commonly Need Heat
The rentals we see most in cold weather are a winter concrete pour that needs warm air while it cures, a remodel or addition where finish work cannot start in the cold, a barn or shop where equipment and materials need to stay above freezing, and thawing a work area or frozen ground cover before digging. If your job is on that list, the deciding questions are just the size of the space, how open it is, and how many days you need to hold the temperature.
Cold-Weather Heating Checklist
- Measure the space: length, width and ceiling height
- Note how closed in it is — windows and doors in, or still open
- Pick fuel: kerosene for the cleanest burn in enclosed areas
- Plan a grounded 120-volt outlet within cord reach of the heater spot
- Plan the ventilation opening before the heater arrives
- Clear 3 feet around the heater and 10 feet in front of it
- Decide how many days you need to hold heat, not just warm up once
Not sure which size your building points to? Call or text Ward’s Equipment Rental in Hamburg at 810-231-7368 with the size of the space and how open it is, and we will size it with you — or browse the heating rentals and tell us about the job when you request one.
