The most common telehandler mistake happens before the machine ever leaves the yard: picking it by the big number on the side. A 6,000 lb machine does not lift 6,000 lb everywhere. It lifts that close in, with the boom down. Stretch the boom out to set a truss or land a pallet in the middle of a building, and the same machine may be good for a fifth of that. Plan the lift at the far end — how high, how far out, and how heavy that farthest pick actually is — and the right machine usually picks itself.
Start With Three Numbers, Not One
Before you call, work out three things about your heaviest, hardest lift. First, the height: where does the load have to end up, not how tall is the building? Second, the forward reach: how far from the front tires will the load be when you set it? A machine parked outside a wall, reaching into the middle of a building, can need most of its reach even on a modest job. Third, the weight at that spot, including the pallet, rigging and anything hanging from a hook.
Write those three numbers down. They matter more than the model name, and they are exactly what we will ask about when you book.
What Our Four SkyTraks Actually Do
Our telehandler fleet runs from 6,000 to 10,000 lb and 34 to 42 feet of lift, and the differences are mostly in what each machine keeps at full stretch.
The SkyTrak 6034 is the compact one: 6,000 lb capacity, 34 ft 5 in of lift and 23 ft 2 in of forward reach, with about 1,000 lb left at full reach. At 14,500 lb and 7 ft 11 in wide, it is the easiest on tight residential lots, and it covers most one- and two-story houses, garages and additions. Day rates start at $445 for up to 24 hours.
The SkyTrak 6042 keeps the same 6,000 lb class but lifts 42 ft 4 in and reaches 29 ft 6 in, with about 1,200 lb at full reach. That extra reach is why it is the pole barn and truss-setting machine, and the one most framers and roofers ask for. It starts at $495 for up to 24 hours.
The SkyTrak 8042 lifts the same 42 ft 4 in and reaches the same 29 ft 6 in, but carries 8,000 lb close in, 6,000 lb at full height and 1,600 lb at full reach. That is the step up for heavier trusses, beams and full pallets. It starts at $545 for up to 24 hours. The SkyTrak 10042 is the heavy end: 10,000 lb capacity, 42 ft 1 in of lift, and — this is the number that matters — still 6,000 lb at full height and at full reach. Its forward reach is a little shorter at 26 ft 9 in, so it trades a few feet of reach for a lot of strength at the far end, which is the right trade for steel, block and heavy pallets placed well out from the machine. It starts at $645 for up to 24 hours.
Whichever machine you take, the load chart in the cab is the final word on a given lift. Operators need to be trained to run a telehandler, and every pick should be planned from that chart, not from the headline capacity.
Attachments Change the Math
Three attachments do most of the extra work on our telehandlers, and each one changes what the machine can lift, so plan them in from the start rather than adding them as an afterthought. The 15 ft truss boom adds reach with a hook for setting trusses and long lumber or steel over a wall; it is listed at 2,000 lb, rents for $100 alongside a telehandler, and the telehandler’s own load chart still governs. The adjustable jib, which runs from 7 to 12 ft, hangs beams, pipe and precast from a hook so they can be lowered into place. The fork-mounted work platform lifts a crew and tools — 1,000 lb listed capacity, people and tools combined — for short work at the eaves when the machine is already on site, with fall protection tied off to the platform required.
Ground, Access and Delivery
Reach planning also means planning where the machine will sit. These are four-wheel-drive diesel machines built for rough ground, but they are heavy: from 14,500 lb for the 6034 up to 26,600 lb for the 10042, and from 7 ft 11 in to 8 ft 6 in wide. In late fall, think about soft lawns, fresh driveways and mud between the road and the building, and give the machine a firm, level spot to work from. If the only good spot is farther from the building, that distance comes straight out of your reach — another reason to measure the farthest set before you book.
Telehandlers go out on our own trucks. Round-trip delivery is $350 within 45 minutes’ drive of our Hamburg yard and $450 for 46 to 75 minutes. Run hours are unlimited; you pay for the time the machine is out, not the hours on the meter.
Telehandler Planning Checklist
- Height of the highest set, measured to where the load lands
- Forward reach from the front tires to that same set
- Weight of the heaviest load at full reach, pallet and rigging included
- Attachment needed: forks, truss boom, jib or work platform
- A firm, level working spot, with the width and ground to get there
- A trained operator, and a plan to check each big pick against the load chart
Not sure which machine your farthest lift points to? Call or text Ward’s Equipment Rental in Hamburg at 810-231-7368 with your height, reach and load weight and we will size it with you, or browse the telehandlers and tell us the job when you request one.
